ST Micro-electronics jobs in Noida

Status
Not open for further replies.
N

nakul

New member
Hi,

ST Micro-electronics is recruiting C Professionals in the firmware and driver
development area. Candidate with 1 year experience can send me there CV on nakulsingh2002@yahoo.com.

The openings need to be filled immediately.


thanks,
Nakul
 
Bhai nakul, Thanks for this valuable information. .. Is there any requirement for PROTOCOL DEVELOPMENT(TCP\IP, UPNP, VOIP..) ? At present I am working on DUAL STACK(IPv4/IPv6) implementation in C lang??
 
there are opening in Conexant & freescale u can mail me ur CV

prashantacmet said:
Bhai nakul, Thanks for this valuable information. .. Is there any requirement for PROTOCOL DEVELOPMENT(TCP\IP, UPNP, VOIP..) ? At present I am working on DUAL STACK(IPv4/IPv6) implementation in C lang??
Click to expand...
 
My Resume

ajaygaite said:
there are opening in Conexant & freescale u can mail me ur CV
Click to expand...

Hi Ajay,
I am Amit Tomar from Noida and thanks for information.I have attached my CV here with this letter.please forward it suitable place.

Thanks & Regards
AMIT TOMAR
9868644940
 
Hi
I m doing job in a Automation Company. Recently I have a project in which I have to do aotomation of a lock. It will work like this:-
When we swap the Identity Card it will match the identity of the person & then open the door if the identity matches.
I think ur Company help me & if not, Can u please help me finding out any company which can do the designing & programming task & prepare 1 product.

I want to know which microcontroller 2 use, design the circiut, programming of that, necessary adjustments can be done to modify the mechanical design.
Thanks n Regards
Vikas Punia
 
Hi Vikash,

you said you word on smart cards, which one ( Contact less, contact, proxy)
Now looking cost & market each cards need different type MCU. but in most case only 8 Bit MCU.

If you want interface chip dat for smart card then i have data on

SCM : contact smart card chip
PHilips: Contact-less smart card chip (14.xMhz)


But in general

For 8 Bit MCUs:
For CISC : X51 core is easy ( Comp. ATMEL, PHILIPS, Dallas are manufacturing this core base MCU) best tool for this is "KEIL"( C cross complier)

for RISC : microchip is good one( good for automation industry). Visit www.microchip.com

for 16 Bit MCUS
TI :MSP430 series( www.ti.com) IAR c-Cross complier required.
Renesas( old Hitachi) : H8 core

For 32 bit:

ARM7/ARM9 : best Processor ( available from lot of comp.)
Some free tool ara available, or use GNU tool chain

Power PC : available from Freescale/IBM & AMCC.
Get free Code-worrier from freescale. (www.freescale.com)


vikas0118 said:
Hi
I m doing job in a Automation Company. Recently I have a project in which I have to do aotomation of a lock. It will work like this:-
When we swap the Identity Card it will match the identity of the person & then open the door if the identity matches.
I think ur Company help me & if not, Can u please help me finding out any company which can do the designing & programming task & prepare 1 product.

I want to know which microcontroller 2 use, design the circiut, programming of that, necessary adjustments can be done to modify the mechanical design.
Thanks n Regards
Vikas Punia
Click to expand...
 
Last edited:
Hi, I am new to our group

I am sending my profile for ST Microelectronics and Conexant.


Plz forward it.


Remember : "We Together Can , We Together Will"


Regards,
Sachin Chauhan
09868772390
 
Status
Not open for further replies.
Back
Top